README ^^^^^^ Contents ^^^^^^^^ o Overview - Description - Fake Interrupts - Timing Fidelity o Debugging o Issues - 64-bit Issues - Compiler differences - Stack Size Issues - Networking Issues - X11 Issues - Cygwin64 Issues - SMP o BASIC o Configurations Overview ^^^^^^^^ Description ----------- This README file describes the contents of the build configurations available for the NuttX "sim" target. The sim target is a NuttX port that runs as a user-space program under Linux or Cygwin. It is a very "low fidelity" embedded system simulation: This environment does not support any kind of asynchronous events -- there are nothing like interrupts in this context. Therefore, there can be no pre-empting events. Fake Interrupts --------------- In order to get timed behavior, the system timer "interrupt handler" is called from the sim target's IDLE loop. The IDLE runs whenever there is no other task running. So, for example, if a task calls sleep(), then that task will suspend wanting for the time to elapse. If nothing else is available to run, then the IDLE loop runs and the timer increments, eventually re-awakening the sleeping task. Context switching is based on logic similar to setjmp() and longjmp(). The sim target is used primarily as a development and test platform for new RTOS features. It is also of academic interest. But it has no real-world application that I know of. Timing Fidelity --------------- NOTE: In order to facility fast testing, the sim target's IDLE loop, by default, calls the system "interrupt handler" as fast as possible. As a result, there really are no noticeable delays when a task sleeps. However, the task really does sleep -- but the time scale is wrong. If you want behavior that is closer to normal timing, then you can define CONFIG_SIM_WALLTIME=y in your configuration file. This configuration setting will cause the sim target's IDLE loop to delay on each call so that the system "timer interrupt" is called at a rate approximately correct for the system timer tick rate. With this definition in the configuration, sleep() behavior is more or less normal. Debugging ^^^^^^^^^ One of the best reasons to use the simulation is that is supports great, Linux- based debugging. Here are the steps that I following to use the Linux ddd graphical front-end to GDB: 1. Modify the top-level configuration file. Enable debug symbols by defining the following. cd CONFIG_DEBUG_SYMBOLS=y 2. Re-build: cd make clean make 3. Then start the debugging: ddd nuttx & gdb> b user_start gdb> r NOTE: This above steps work fine on both Linux and Cygwin. On Cygwin, you will need to start the Cywin-X server before running ddd. Issues ^^^^^^ 64-Bit Issues ------------- As mentioned above, context switching is based on logic like setjmp() and longjmp(). This context switching is available for 32-bit and 64-bit targets. You must, however, set the correct target in the configuration before you build: CONFIG_HOST_X86_64 or CONFIG_HOST_X86 for 64- and 32-bit targets, respectively. On a 64-bit machine, you can also force the 32-bit build with CONFIG_SIM_M32=y (which does not seem to be supported by more contemporary x86_64 compilers). There are other 64-bit issues as well. For example, addresses are retained in 32-bit unsigned integer types in a few places. On a 64-bit machine, the 32-bit address storage may corrupt 64-bit addressing. NOTE: This is really a bug -- addresses should not be retained in uint32_t types but rather in uintptr_t types to avoid issues just like this. Compiler differences -------------------- operator new: Problem: "'operator new' takes size_t ('...') as first parameter" Workaround: Add -fpermissive to the compilation flags Stack Size Issues ----------------- When you run the NuttX simulation, it uses stacks allocated by NuttX from the NuttX heap. The memory management model is exactly the same in the simulation as it is real, target system. This is good because this produces a higher fidelity simulation. However, when the simulation calls into Linux/Cygwin libraries, it will still use these small simulation stacks. This happens, for example, when you call into the system to get and put characters to the console window or when you make x11 calls into the system. The programming model within those libraries will assume a Linux/Cygwin environment where the stack size grows dynamically and not the small, limited stacks of a deeply embedded system. As a consequence, those system libraries may allocate large data structures on the stack and overflow the small NuttX stacks. X11, in particular, requires large stacks. If you are using X11 in the simulation, make sure that you set aside a "lot" of stack for the X11 system calls (maybe 8 or 16Kb). The stack size for the thread that begins with user start is controlled by the configuration setting CONFIG_USERMAIN_STACKSIZE; you may need to increase this value to larger number to survive the X11 system calls. If you are running X11 applications as NSH add-on programs, then the stack size of the add-on program is controlled in another way. Here are the steps for increasing the stack size in that case: cd ../apps/builtin # Go to the builtin apps directory vi builtin_list.h # Edit this file and increase the stack size of the add-on rm .built *.o # This will force the builtin apps logic to rebuild Networking Issues ----------------- I never did get networking to work on the sim target. It tries to use the tap device (/dev/net/tun) to emulate an Ethernet NIC, but I never got it correctly integrated with the NuttX networking (I probably should try using raw sockets instead). Update: Max Holtzberg reports to me that the tap device actually does work properly, but not in an NSH configuration because of stdio operations freeze the simulation. REVISIT: This may not long be an issue even with NSH because of the recent redesign of how the stdio devices are handled in the simulation (they should no longer freeze the simulation). X11 Issues ---------- There is an X11-based framebuffer driver that you can use exercise the NuttX graphics subsystem on the simulator (see the sim/nx11 configuration below). This may require a lot of tinkering to get working, depending upon where your X11 installation stores libraries and header files and how it names libraries. For example, on UBuntu 9.09, I had to do the following to get a clean build: cd /usr/lib/ sudo ln -s libXext.so.6.4.0 libXext.so (I also get a segmentation fault at the conclusion of the NX test -- that will need to get looked into as well). The X11 examples builds on Cygwin, but does not run. The last time I tried it, XOpenDisplay() aborted the program. UPDATE: This was caused by the small stack size and can be fixed by increasing the size of the NuttX stack that calls into X11. See the discussion "Stack Size Issues" above. Cygwin64 Issues --------------- There are some additional issues using the simulator with Cygwin64. Below is the summary of the changes that I had to make to get the simulator working in that environment: CONFIG_HOST_X86_64=y CONFIG_SIM_M32=n Need to select X64_64. Cygwin64 tools do not seem to support any option to build a 32-bit target. CONFIG_SIM_CYGWIN_DECORATED=n Older versions of Cygwin toolsdecorated C symbol names by adding an underscore to the beginning of the symbol name. Newer versions of Cygwin do not seem to do this. Deselecting CONFIG_SIM_CYGWIN_DECORATED will select the symbols without the leading underscore as needed by the Cygwin64 toolchain. How do you know if you need this option? You could look at the generated symbol tables to see if there are underscore characters at the beginning of the symbol names. Or, if you need this option, the simulation will not run: It will crash early, probably in some function due to the failure to allocate memory. In this case, when I tried to run nutt.exe from the command line, it exited silently. Running with GDB I get following (before hitting a breakpoint at main()): (gdb) r Starting program: /cygdrive/c/Users/Gregory/Documents/projects/nuttx/master/nuttx/nuttx.exe [New Thread 6512.0xda8] [New Thread 6512.0x998] 1 [main] nuttx 6512 C:\Users\Gregory\Documents\projects\nuttx\master\nuttx\nuttx.exe: *** fatal error - Internal error: Out of memory for new path buf. 736 [main] nuttx 6512 cygwin_exception::open_stackdumpfile: Dumping stack trace to nuttx.exe.stackdump [Thread 6512.0x998 exited with code 256] [Inferior 1 (process 6512) exited with code 0400] CONFIG_SIM_X8664_SYSTEMV=n CONFIG_SIM_X8664_MICROSOFT=y Selet Microsoft x64 calling convention. The Microsoft x64 calling convention is followed on Microsoft Windows and pre-boot UEFI (for long mode on x86-64). It uses registers RCX, RDX, R8, R9 for the first four integer or pointer arguments (in that order), and XMM0, XMM1, XMM2, XMM3 are used for floating point arguments. Additional arguments are pushed onto the stack (right to left). Integer return values (similar to x86) are returned in RAX if 64 bits or less. Floating point return values are returned in XMM0. Parameters less than 64 bits long are not zero extended; the high bits are not zeroed. SMP --- The configuration has basic support SMP testing. The simulation supports the emulation of multiple CPUs by creating multiple pthreads, each run a copy of the simulation in the same process address space. At present, the SMP simulation is not fully functional: It does operate on the simulated CPU threads for a few context switches then fails during a setjmp() operation. I suspect that this is not an issue with the NuttX SMP logic but more likely some chaos in the pthread controls. I have seen similar such strange behavior other times that I have tried to use setjmp/longmp from a signal handler! Like when I tried to implement simulated interrupts using signals. Apparently, if longjmp is invoked from the context of a signal handler, the result is undefined: http://www.open-std.org/jtc1/sc22/wg14/www/docs/n1318.htm You can enable SMP for ostest configuration by enabling: +CONFIG_SPINLOCK=y +CONFIG_SMP=y +CONFIG_SMP_NCPUS=2 +CONFIG_SMP_IDLETHREAD_STACKSIZE=2048 You also must enable near-realtime-performance otherwise even long timeouts will expire before a CPU thread even has a chance to execute. -# CONFIG_SIM_WALLTIME is not set +CONFIG_SIM_WALLTIME=y And you can enable some additional debug output with: -# CONFIG_DEBUG_SCHED is not set +CONFIG_DEBUG_SCHED=y -# CONFIG_SCHED_INSTRUMENTATION is not set +CONFIG_SCHED_INSTRUMENTATION=y The SMP configuration will run with: CONFIG_SMP_NCPUS=1 In this case there is, of course, no muli-CPU processing, but this does verify the correctness of some the basic SMP logic. The NSH configuration can also be forced to run SMP, but suffers from the same quirky behavior. I can be made reliable if you modify arch/sim/src/up_idle.c so that the IDLE loop only runs for CPU0. Otherwise, often simuart_post() will be called from CPU1 and it will try to restart NSH on CPU0 and, again, the same quirkiness occurs. But for example, this command: nsh> sleep 1 & will execute the sleep command on CPU1 which has worked every time that I have tried it (which is not too many times). BASIC ^^^^^ I have used the sim/nsh configuration to test Michael Haardt's BASIC interpreter that you can find at apps/interpreters/bas. Bas is an interpreter for the classic dialect of the programming language BASIC. It is pretty compatible to typical BASIC interpreters of the 1980s, unlike some other UNIX BASIC interpreters, that implement a different syntax, breaking compatibility to existing programs. Bas offers many ANSI BASIC statements for structured programming, such as procedures, local variables and various loop types. Further there are matrix operations, automatic LIST indentation and many statements and functions found in specific classic dialects. Line numbers are not required. There is also a test suite for the interpreter that can be found at apps/examples/bastest. Configuration ------------- Below are the recommended configuration changes to use BAS with the stm32f4discovery/nsh configuration: Dependencies: CONFIG_LIBC_EXECFUNCS=y : exec*() functions are required CONFIG_LIBM=y : Some floating point library is required CONFIG_LIBC_FLOATINGPOINT=y : Floating point printing support is required CONFIG_LIBC_TMPDIR="/tmp" : Writeable temporary files needed for some commands Enable the BASIC interpreter. Other default options should be okay: CONFIG_INTERPRETERS_BAS=y : Enables the interpreter CONFIG_INTERPRETER_BAS_VT100=y The BASIC test suite can be included: CONFIG_FS_ROMFS=y : ROMFS support is needed CONFIG_EXAMPLES_BASTEST=y : Enables the BASIC test setup CONFIG_EXAMPLES_BASTEST_DEVMINOR=6 CONFIG_EXAMPLES_BASTEST_DEVPATH="/dev/ram6" Usage ----- This setup will initialize the BASIC test (optional): This will mount a ROMFS file system at /mnt/romfs that contains the BASIC test files: nsh> bastest Registering romdisk at /dev/ram6 Mounting ROMFS filesystem at target=/mnt/romfs with source=/dev/ram6 nsh> The interactive interpreter is started like: nsh> bas bas 2.4 Copyright 1999-2014 Michael Haardt. This is free software with ABSOLUTELY NO WARRANTY. > Ctrl-D exits the interpreter. The test programs can be ran like this: nsh> bastest Registering romdisk at /dev/ram0 Mounting ROMFS filesystem at target=/mnt/romfs with source=/dev/ram0 nsh> bas /mnt/romfs/test01.bas 1 hello 0.0002 0.0000020 0.0000002 nsh> Or you can load a test into memory and execute it interactively: nsh> bas bas 2.4 Copyright 1999-2014 Michael Haardt. This is free software with ABSOLUTELY NO WARRANTY. > load "/mnt/romfs/test01.bas" > run 1 hello 0.0002 0.0000020 0.0000002 > Configurations ^^^^^^^^^^^^^^ Common Configuration Information -------------------------------- 1. Each configuration is maintained in a sub-directory and can be selected as follow: cd /tools ./configure.sh sim/ cd - Where is one of the following sub-directories. 2. All configurations uses the mconf-based configuration tool. To change this configuration using that tool, you should: a. Build and install the kconfig mconf tool. See nuttx/README.txt see additional README.txt files in the NuttX tools repository. b. Execute 'make menuconfig' in nuttx/ in order to start the reconfiguration process. 3. Before building, make sure that the configuration is correct for you host platform: a. Linux, 32-bit CPU CONFIG_HOST_LINUX=y CONFIG_HOST_WINDOWS=n CONFIG_HOST_X86=y CONFIG_HOST_X86_64=n b. Linux, 64-bit CPU, 32-bit build CONFIG_HOST_LINUX=y CONFIG_HOST_WINDOWS=n CONFIG_HOST_X86=n CONFIG_HOST_X86_64=y CONFIG_SIM_X8664_MICROSOFT=n CONFIG_SIM_X8664_SYSTEMV=y CONFIG_SIM_M32=y c. Linux, 64-bit CPU, 64-bit build CONFIG_HOST_LINUX=y CONFIG_HOST_WINDOWS=n CONFIG_HOST_X86=n CONFIG_HOST_X86_64=y CONFIG_SIM_X8664_MICROSOFT=n CONFIG_SIM_X8664_SYSTEMV=y CONFIG_SIM_M32=n d. Cygwin, 32-bit CONFIG_HOST_LINUX=n CONFIG_HOST_WINDOWS=y CONFIG_WINDOWS_CYGWIN=y CONFIG_HOST_X86=y CONFIG_HOST_X86_64=n e. Cygwin64, 64-bit, 32-bit build I don't believe this configuration is supported by Cygwin64 f. Cygwin64, 64-bit, 64-bit build CONFIG_HOST_LINUX=n CONFIG_HOST_WINDOWS=y CONFIG_WINDOWS_CYGWIN=y CONFIG_HOST_X86=n CONFIG_HOST_X86_64=y CONFIG_SIM_X8664_MICROSOFT=y CONFIG_SIM_X8664_SYSTEMV=n CONFIG_SIM_M32=n Configuration Sub-Directories ----------------------------- configdata A unit test for the MTD configuration data driver. cxxtest The C++ standard libary test at apps/examples/cxxtest configuration. This test is used to verify the uClibc++ port to NuttX. NOTES ----- 1. Before you can use this example, you must first install the uClibc++ C++ library. This is located outside of the NuttX source tree in the NuttX uClibc++ GIT repository. See the README.txt file there for instructions on how to install uClibc++ 2. At present (2012/11/02), exceptions are disabled in this example CONFIG_UCLIBCXX_EXCEPTION=n). It is probably not necessary to disable exceptions. 3. Unfortunately, this example will not run now. The reason that the example will not run on the simulator has to do with when static constructors are enabled: In the simulator it will attempt to execute the static constructors before main() starts. BUT... NuttX is not initialized and this results in a crash. To really use this example, I will have to think of some way to postpone running C++ static initializers until NuttX has been initialized. ipforward This is an NSH configuration that includes a simple test of the NuttX IP forwarding logic using apps/examples/ipforward. That example uses two TUN network devices to represent two networks. The test then sends packets from one network destined for the other network. The NuttX IP forwarding logic will recognize that the received packets are not destined for it and will forward the logic to the other TUN network. The application logic then both sends the packets on one network and receives and verifies the forwarded packet recieved on the other network. The received packets differ from the sent packets only in that the hop limit (TTL) has been decremented. Be default, this test will forward TCP packets. The test can be modified to support forwarding of ICMPv6 multicast packets with these changes to the .config file: -CONFIG_EXAMPLES_IPFORWARD_TCP=y +CONFIG_EXAMPLES_IPFORWARD_ICMPv6=y +CONFIG_NET_ICMPv6=y +CONFIG_NET_ICMPv6_PING=y +CONFIG_NET_ETHERNET=y +CONFIG_NET_IPFORWARD_BROADCAST=y Additional required settings will also be selected when you manually select the above via 'make menuconfig'. minibasic This configuration was used to test the Mini Basic port at apps/interpreters/minibasic. mount Configures to use apps/examples/mount. mtdpart This is the apps/examples/mtdpart test using a MTD RAM driver to simulate the FLASH part. mtdrwb This is the apps/examples/mtdrwb test using a MTD RAM driver to simulate the FLASH part. nettest Configures to use apps/examples/nettest. This configuration enables networking using the network TAP device. NOTES: 1. The NuttX network is not, however, functional on the Linux TAP device yet. UPDATE: The TAP device does apparently work according to a NuttX user (provided that it is not used with NSH: NSH waits on readline() for console input. When it calls readline(), the whole system blocks waiting from input from the host OS). My failure to get the TAP device working appears to have been a cockpit error. 2. As of NuttX-5.18, when built on Windows, this test does not try to use the TAP device (which is not available on Cygwin anyway), but inside will try to use the Cygwin WPCAP library. Only the most preliminary testing has been performed with the Cygwin WPCAP library, however. NOTE that the IP address is hard-coded in arch/sim/src/up_wpcap.c. You will either need to edit your configuration files to use 10.0.0.1 on the "target" (CONFIG_EXAMPLES_NETTEST_*) or edit up_wpcap.c to select the IP address that you want to use. nsh Configures to use the NuttShell at apps/examples/nsh. NOTES: 1. This version has one builtin function: This configuration: apps/examples/hello. 2. This version has password protection enable. Here is the login: USERNAME: admin PASSWORD: Adminstrator The encrypted password is retained in /etc/passwd. I am sure that you will find this annoying. You can disable the password protection by de-selecting CONFIG_NSH_CONSOLE_LOGIN=y. 3. This configuration has BINFS enabled so that the builtin applications can be made visible in the file system. Because of that, the build in applications do not work as other examples. For example trying to execute the hello builtin application will fail: nsh> hello nsh: hello: command not found nsh> Unless you first mount the BINFS file system: nsh> mount -t binfs /bin nsh> ls /bin /bin: hello nsh> echo $PATH /bin nsh> hello Hello, World!! nsh> Notice that the executable 'hello' is found using the value in the PATH variable (which was preset to "/bin"). If the PATH variable were not set then you would have to use /bin/hello on the command line. nsh2 This is another example that configures to use the NuttShell at apps/examples/nsh. Like nsh, this version uses NSH built-in functions: The nx, nxhello, and nxlines examples are included as built-in functions. NOTES: 1. X11 Configuration This configuration uses an X11-based framebuffer driver. Of course, this configuration can only be used in environments that support X11! (And it may not even be usable in all of those environments without some "tweaking" See discussion below under the nx11 configuration). nx Configures to use apps/examples/nx. NOTES: 1. Special Framebuffer Configuration Special simulated framebuffer configuration options: CONFIG_SIM_FBHEIGHT - Height of the framebuffer in pixels CONFIG_SIM_FBWIDTH - Width of the framebuffer in pixels. CONFIG_SIM_FBBPP - Pixel depth in bits 2. No Display! This version has NO DISPLAY and is only useful for debugging NX internals in environments where X11 is not supported. There is and additonal configuration that may be added to include an X11- based simulated framebuffer driver: CONFIG_SIM_X11FB - Use X11 window for framebuffer See the "nx11" configuration below for more information. 3. Multi- and Single-User Modes The default is the single-user NX implementation. To select the multi-user NX implementation: CONFG_NX_MULTIUSER=y CONFIG_DISABLE_MQUEUE=n nx11 Configures to use apps/examples/nx. This configuration is similar to the nx configuration except that it adds support for an X11- based framebuffer driver. Of course, this configuration can only be used in environments that support X11! (And it may not even be usable in all of those environments without some "tweaking"). 1. Special Framebuffer Configuration This configuration uses the same special simulated framebuffer configuration options as the nx configuration: CONFIG_SIM_X11FB - Use X11 window for framebuffer CONFIG_SIM_FBHEIGHT - Height of the framebuffer in pixels CONFIG_SIM_FBWIDTH - Width of the framebuffer in pixels. CONFIG_SIM_FBBPP - Pixel depth in bits 2. X11 Configuration But now, since CONFIG_SIM_X11FB is also selected the following definitions are needed CONFIG_SIM_FBBPP (must match the resolution of the display). CONFIG_FB_CMAP=y My system has 24-bit color, but packed into 32-bit words so the correct setting of CONFIG_SIM_FBBPP is 32. For whatever value of CONFIG_SIM_FBBPP is selected, the corresponding CONFIG_NX_DISABLE_*BPP setting must not be disabled. 3. Touchscreen Support A X11 mouse-based touchscreen simulation can also be enabled by setting: CONFIG_INPUT=y CONFIG_SIM_TOUCHSCREEN=y Then you must also have some application logic that will call board_tsc_setup(0) to register the touchscreen driver. See also configuration "touchscreen" NOTES: a. If you do not have the call to sim_tcinitialize(0), the build will mysteriously fail claiming that is can't find up_tcenter() and up_tcleave(). That is a consequence of the crazy way that the simulation is built and can only be eliminated by calling up_simtouchscreen(0) from your application. b. You must first call up_fbinitialize(0) before calling up_simtouchscreen() or you will get a crash. c. Call sim_tcunininitializee() when you are finished with the simulated touchscreen. d. Enable CONFIG_DEBUG_INPUT=y for touchscreen debug output. 4. X11 Build Issues To get the system to compile under various X11 installations you may have to modify a few things. For example, in order to find libXext, I had to make the following change under Ubuntu 9.09: cd /usr/lib/ sudo ln -s libXext.so.6.4.0 libXext.so 5. Multi- and Single-User Modes The default is the single-user NX implementation. To select the multi-user NX implementation: CONFG_NX_MULTIUSER=y CONFIG_DISABLE_MQUEUE=n 6. apps/examples/nxterm This configuration is also set up to use the apps/examples/nxterm test instead of apps/examples/nx. To enable this configuration, First, select Multi-User mode as described above. Then add the following definitions to the defconfig file: -CONFIG_NXTERM=n +CONFIG_NXTERM=y -CONFIG_NX_MULTIUSER=n +CONFIG_NX_MULTIUSER=y -CONFIG_EXAMPLES_NX=y +CONFIG_EXAMPLES_NX=n -CONFIG_EXAMPLES_NXTERM=n +CONFIG_EXAMPLES_NXTERM=y See apps/examples/README.txt for further details. nxffs This is the apps/examples/nxffs test using a MTD RAM driver to simulate the FLASH part. nxlines This is the apps/examples/nxlines test. nxwm This is a special configuration setup for the NxWM window manager UnitTest. The NxWM window manager can be found here: nuttx-code/NxWidgets/nxwm The NxWM unit test can be found at: nuttx-code/NxWidgets/UnitTests/nxwm Documentation for installing the NxWM unit test can be found here: nuttx-code/NxWidgets/UnitTests/READEM.txt NOTES 1. There is an issue with running this example under the simulation. In the default configuration, this example will run the NxTerm example which waits on readline() for console input. When it calls readline(), the whole system blocks waiting from input from the host OS. So, in order to get this example to run, you must comment out the readline call in apps/nshlib/nsh_consolemain.c like: Index: nsh_consolemain.c =================================================================== --- nsh_consolemain.c (revision 4681) +++ nsh_consolemain.c (working copy) @@ -117,7 +117,8 @@ /* Execute the startup script */ #ifdef CONFIG_NSH_ROMFSETC - (void)nsh_script(&pstate->cn_vtbl, "init", NSH_INITPATH); +// REMOVE ME +// (void)nsh_script(&pstate->cn_vtbl, "init", NSH_INITPATH); #endif /* Then enter the command line parsing loop */ @@ -130,7 +131,8 @@ fflush(pstate->cn_outstream); /* Get the next line of input */ - +sleep(2); // REMOVE ME +#if 0 // REMOVE ME ret = readline(pstate->cn_line, CONFIG_NSH_LINELEN, INSTREAM(pstate), OUTSTREAM(pstate)); if (ret > 0) @@ -153,6 +155,7 @@ "readline", NSH_ERRNO_OF(-ret)); nsh_exit(&pstate->cn_vtbl, 1); } +#endif // REMOVE ME } /* Clean up */ UPDATE: I recently implemented a good UART simulation to driver the serial console. So I do not believe that problem exists and I think that the above workaround should no longer be necessary. However, I will leave the above text in place until I get then oppotunity to verify that the new UART simulation fixes the problem. ostest The "standard" NuttX apps/examples/ostest configuration. pashello Configures to use apps/examples/pashello. pf_ieee802154 This is the configuration that used for unit level test of the socket support for the PF_IEEE802154 address family. It uses the IEEE 802.15.4 loopback network driver and the test at apps/examples/pf_ieee802154. Basic usage example: nsh> pfserver ab:cd & nsh> pfclient ab:cd pktradio This configuration is identical to the 'sixlowpan configuration described below EXCEPT that is uses the genericl packet radio loopback network device. sixlowpan This configuration was intended only for unit-level testing of the 6LoWPAN stack. It enables networking with 6LoWPAN support and uses only a IEEE802.15.4 MAC loopback network device to supported testing. This configuration includes apps/examples/nettest and apps/examples/udpblaster. Neither are truly functional. The only intent of this configuration is to verify that the 6LoWPAN stack correctly encodes IEEE802.15.4 packets on output to the loopback device and correctly decodes the returned packet. See also the 'pktradio' configuration. touchscreen This configuration uses the simple touchscreen test at apps/examples/touchscreen. This test will create an empty X11 window and will print the touchscreen output as it is received from the simulated touchscreen driver. Since this example uses the simulated frame buffer driver, the most of the configuration settings discussed for the "nx11" configuration also apply here. See that discussion above. See apps/examples/README.txt for further information about build requirements and configuration settings. traveler Configures to build the Traveler first person, 3-D ray casting game at apps/graphics/traveler. This configuration derives fromthe nx11 configuration and many of the comments there appear here as well. This configuration defpends on X11 and, of course, can only be used in environments that support X11! (And it may not even be usable in all of those environments without some "tweaking"). 1. Special Framebuffer Configuration This configuration uses the same special simulated framebuffer configuration options as the nx configuration: CONFIG_SIM_X11FB - Use X11 window for framebuffer CONFIG_SIM_FBHEIGHT - Height of the framebuffer in pixels CONFIG_SIM_FBWIDTH - Width of the framebuffer in pixels. CONFIG_SIM_FBBPP - Pixel depth in bits 2. X11 Configuration But now, since CONFIG_SIM_X11FB is also selected the following definitions are needed CONFIG_SIM_FBBPP (must match the resolution of the display). CONFIG_FB_CMAP=y My system has 24-bit color, but packed into 32-bit words so the correct setting of CONFIG_SIM_FBBPP is 32. 3. X11 Build Issues To get the system to compile under various X11 installations you may have to modify a few things. For example, in order to find libXext, I had to make the following change under Ubuntu 9.09: cd /usr/lib/ sudo ln -s libXext.so.6.4.0 libXext.so udgram This is the same as the nsh configuration except that it includes two addition build in applications: server and client. These applications are provided by the test at apps/examples/udgram. This configuration enables local, Unix domain sockets and supports the test of the datagram sockets. To use the test: nsh> mount -t binfs /bin nsh> server & nsh> client For the sake of sanity, binfs and logins are disabled in this configuration. unionfs This is a version of NSH dedicated to performing the simple test of the Union File System at apps/exmaples/uniofs. The command 'unionfs' will mount the Union File System at /mnt/unionfs. You can than compare what you see at /mnt/unionfs with the content of the ROMFS file systems at apps/examples/unionfs/atestdir and btestdir. Here is some sample output from the test: NuttShell (NSH) nsh> unionfs Mounting ROMFS file system 1 at target=/mnt/a with source=/dev/ram4 Mounting ROMFS file system 2 at target=/mnt/b with source=/dev/ram5 nsh> ls /mnt/unionfs /mnt/unionfs: . afile.txt offset/ When unionfs was created, file system was joined with and offset called offset". Therefore, all of the file system 2 root contents will appear to reside under a directory called offset/ (although there is no directory called offset/ on file system 2). Fie system 1 on the other hand does have an actual directory called offset/. If we list the contents of the offset/ directory in the unified file system, we see he merged content of the file system 1 offset/ directory and the file system 2 root directory: nsh> cat /mnt/unionfs/afile.txt This is a file in the root directory on file system 1 nsh> ls /mnt/unionfs/offset /mnt/unionfs/offset: afile.txt . adir/ bfile.txt bdir/ nsh> cat /mnt/unionfs/offset/afile.txt This is a file in the offset/ directory on file system 1 nsh> cat /mnt/unionfs/offset/bfile.txt This is another file in the root directory on file system 2 The directory offset/adir exists on file system 1 and the directory\ adir/ exists on file system 2. You can see that these also overlap: nsh> ls /mnt/unionfs/offset/adir /mnt/unionfs/offset/adir: .. asubdir/ adirfile.txt bsubdir/ bdirfile.txt . The unified directory listing is showing files from both file systems in their respective offset adir/ subdirectories. The file adirfile.txt exists in both file system 1 and file system 2 but the version if file system 2 is occluded by the version in file system 1. The only way that you can which are looking at is by cat'ing the file: nsh> cat /mnt/unionfs/offset/adir/adirfile.txt This is a file in directory offset/adir on file system 1 The file on file system 1 has correctly occluded the file with the same name on file system 2. bdirfile.txt, however, only exists on file system 2, so it is not occluded: nsh> cat /mnt/unionfs/offset/adir/bdirfile.txt This is another file in directory adir on file system 2 You can see the files in the two file systems before they were unified at apps/examples/unionfs/atestdir and btestdir. ustream This is the same as the nsh configuration except that it includes two addition built in applications: server and client. These applications are provided by the test at apps/examples/ustream. This configuration enables local, Unix domain sockets and supports the test of the stream sockets. To use the test: nsh> mount -t binfs /bin nsh> server & nsh> client